Wire up a new pickguard for a Fender American elite strat?



Asked by: Tim Sigl

How do you wire pickguards?






Joint. Now to replace the ground wire for the tremolo. Claw. Look at that solder melt. Perfect we're gonna stuff that wire. Back into the body a little bit. And we should be ready to go.

How do you change a Fender Strat pickguard?

So I suggest using a thin cloth or a rag that you can wrap under and around the knobs. So you don't damage the knob next I want to pull the switch cap.

How do you load a strat pickguard?

Needs to happen up under here under a 22 fret neck. You don't really see the end of the fingerboard. So as long as it's snug along the side you're fine.

How do you attach pickguard pickups?

Right so we're going to take the pickguard. First thing we're going to do there are three wires to connect. The hot the ground wire coming from the output jack to the main volume control.

Do you have to solder to change pickguard?





All you need is a screwdriver, soldering iron and solder, and maybe something to help you put the bridge springs back in place. The YJM Fury pickguard would be the most complicated model to install due to the lack of a Liberator solderless pot, but even so it’s still a cinch to install.

What wire does fender use?

Widely used in the guitar world for optimal results, is 22AWG wire. This is mainly because you ideally want your wiring AWG to be the same or greater than the guitar’s pickup wire AWG and in most cases pickup manufacturer’s use 22AWG.

Is it easy to change strat pickguard?

Replacing your pickguard is a relatively simple undertaking, but as with any guitar mod, it’s important to plan ahead by having the right tools and understanding each step of the operation.

How do you replace pick guards?

And you can easily just roll this off with your finger like this. And it pretty much come off like. This. Okay okay we mostly have it off but there's still a little bit remaining.

Can you change pickguard without removing strings?

You can remove a strat pickguard without removing the strings IF it is a 21 fret neck. Just loosen the strings, and tape the body on the side you’re pulling it out so you don’t scratch the finish.



How do you solder a Strat pickup?

Just a little bit of solder. On the soldering tip and that'll make it hot enough to melt. That solder joint and just take those wires off if you try to do it without Tinian.

How do you put new pickups in a Stratocaster?

The first step is to take the old pickups. Out I've already unstrung the guitar and remove the pick guard here so that you can see. And in this case. I'm just going to be take unsoldering.

How do you mount a single coil pickup?

To mount the pickups. Directly into the body I'll be using the three-quarter inch long number four sheet metal screw. And I'll just simply position the pickup. Into the pocket.



How do you install a pickup spring?

Run the spring right onto the screw. And then using your finger just go ahead and push the spring into the straw. And then use the plate the arm. To hold the spring tight.

How do you direct mount a guitar pickup?

If you just screwed it flat to the surface of the instrument. That might work if you could use a small screw.

Can I replace a single coil with a humbucker?

Single coils are relatively low in output. So you might be looking for a heavier tone or a little more rock in tone. And you want to switch to two humbuckers.

How do you wire a Strat on a humbucker?

We're going to be using both of capacitors so point is 0 4 7 that's going to be on our tone control for the single coils and a point 0 T 2 which is going to be the tone control for the humbucker.



Which is better humbucker or single coil?

Single-coil pickups tend to have brighter, crisper tone. Comparitively, humbuckers typically have what guitarists describe as a “thicker” sound; one that is perceived as rounder and warmer. Humbuckers also tend to emphasize the sustain produced by the guitar’s tonewoods.