What order should I use guitar amp, sims and cabs in?



Asked by: Brad Martinez

How do you use a guitar amp on Sims?





A PC can be used as a guitar amp by installing an amp sim (guitar amp simulator). Then, connect your guitar to an audio interface input, and the audio interface via USB to the PC running the amp sim. Finally, connect speakers or headphones to the audio interface output, for a working guitar amp.

How do you use an amp sim in real cab?


Happen. First off you're going to need an interface. Something you can send a signal out of you're going to need a cable you will need a power amp. And of course a cabinet and for microphones.

How do you match amp and cab?

Just like the orange most amps will happily power either to 16 ohm cabs or a single 8 ohm loads. And all some amps especially bass amplifiers. You can even drop down to 4 ohms.

Where does amp simulator go in chain?

And the end of the chain.

How do I make my amp sims sound more realistic?





Do Your Amp Sims Sound Bad? 11 Tips For A Better Sound

  1. 1 Use an IR (Impulse Response) …
  2. 2 Use specialist digital audio drivers. …
  3. 3 Use a noise gate with high gain sounds. …
  4. 4 Set the audio interface input level higher. …
  5. 5 Set the audio interface input level lower. …
  6. 6 Set the optimum input level in the amp sim itself.

How do you use the amp simulator Pedal?

How Can I Use Them? Simply plugin your guitar to your amp simulator pedal and then plug that into whichever output you choose such as an amp. Then turn it on and you’re ready to go! Not complex at all, you’ll have to decide for yourself though how you want to adjust your settings.

How can I make my amp sound better?

Getting a Good Clean Tone

  1. Select your clean channel or turn the gain down if you don’t have multiple channels. …
  2. Turn off all amp effects and effect pedals. …
  3. Bring the bass, mid & treble knobs all to 12 o’clock. …
  4. Keep the gain fairly low and adjust the volume to a suitable level. …
  5. Jam for a while to get a feel for the tone.

Can I use my combo amp as a cabinet?

The Quick Answer. You can use a combo amp as a head unit, or as a cabinet in a stack setup by connecting it to the external speaker or head unit that you’re trying to use, respectively.

What does a cab simulator do?

Either a hardware circuit or a DSP model that creates the tonal effects of running an instrument — typically electric guitar or bass — amplifier through a speaker. This allows instruments to be run direct, without miking a speaker, yet still have the coloration that a speaker imparts on the signal.



How do you set up an amp simulator?

Application means you just download whatever amp sim you're using open it up the window pops up then you just plug your guitar into the interface.

Can you use pedals with an amp sim?

There shouldn’t be any problem in running through some pedals, then to your sound cards input(s) to then color it with software amp sims, I’ve done this with my hardware & amp sims, getting a certain tone in 1st.

Does the order of guitar pedals matter?

The order of your pedals matter



The order in which the pedals are set up matter because the signal is being processed multiple times if you have multiple pedals. A general rule of thumb is to first set your distortion and drive pedals first, followed by your modulation pedals like echo, chorus, flanger, tremolo, etc.



Does reverb go before or after delay?

In a guitar signal chain, the delay unit is generally placed before a reverb pedal, but it’s up to the individual musician to decide on the order. Putting delay before reverb can muddy up the sound, so most guitarists prefer placing it after the delay.

Where does acoustic simulator go on pedalboard?

Thanks. The manual recommends putting the acoustic simulator before all other effects. This probably will give you the most acoustic-like tone since the signal the pedal receives will not be colored by other pedals.

Where should I put my preamp pedal in my chain?

A preamp pedal should be placed quite early in your overall signal chain, and obviously before power amp or cab simulator pedals. As it’s a substitute for an amp’s preamp, it should therefore be one of the first stompboxes that your guitar’s output signal comes into contact with.

Where should a compressor go in the signal chain?

And the one that’s closest to our hearts: where do you place the compressor in your signal chain? The Official Textbook of Pedal Placement™ states that, apart from vintage fuzz and wah, compression should always be first in the chain.