(Solved) Intonation Problem (Only with High E and B Strings) in Acoustic Guitar?



Asked by: Morgan Williams

Why does my B and E string sound out of tune?





This is why the B- string sounds out of tune. It’s because the G string and B string are a major third different from each other, and in the Equal Temperament tuning system, the Major Third is 14 cents sharp in comparison to the Just Intonation system, which is 100% accurate.

How do you fix a sharp intonation on an acoustic guitar?

It can be controlled by tightening or loosening the truss rod, which is located in the neck. Essentially, the technician is trying to get everything right before actually adjusting the acoustic guitar’s intonation. This removes the extra variables and makes it easier to dial in the intonation.

Does string height affect intonation?

The intonation is affected by the length of the guitar string. A high action (string height) can negatively impact the intonation of your guitar. This is because, the higher the action, the further you need to press down to fret a note. So when you push down more, you’re essentially lengthening the string.

How do you fix a guitar intonation problem?

As strings age, intonation “drifts” and you’ll naturally start to hear some out-of-tuneness across the fretboard. If this is the case, don’t adjust your intonation, just change your dang strings. Once you’ve installed and thoroughly stretched your new set of strings, then set your intonation.

Why does my B string sound like my E string?





If the strings are properly in place, my guess is that the string is either too tight or too loose. So, instead of the usual E that it’s supposed to be, you see a B. Just tune it until it gets to E. Just make sure to understand if you have to loosen it or tighten it.

Why is my high E out of tune?

A loose or leaning saddle can change the length of the string and affect intonation. Be sure that the saddle is properly positioned in the slot in the bridge and not leaning either way. If you take all the strings off at once to re-string, it is possible for the saddle to change position.

How do you flatten intonation on an acoustic guitar?

Half the width of the nut to make the second string break angle farther up what we're doing is increasing the entire scale length of the guitar.

How do you reset intonation?

No matter what you're doing the concept is the same we're changing the length of the string by moving the saddles. Forward or backward. Making these adjustments we'll pull the string out of tune.

Does nut height affect intonation?

High strings at the nut can cause sharp intonation and make playing in first position difficult, while low or worn slots can result in open-string fret buzz. Generally, the bottoms of the nut slots should be a few thousandths of an inch higher than the tops of the frets when the neck is straight.



What causes intonation problems?

A worn down or improperly positioned nut can cause bad intonation. A worn-down nut will need replacement, and a nut set too high should be filed down in order to lower the string action.

Can new strings affect intonation?

Your guitar’s intonation will likely need to be fine-tuned whenever you replace your strings. If you change string gauges, the intonation will almost certainly need to be reset because the core of your new strings will have a different diameter.

Does neck relief affect intonation?

Adding relief (increasing the amount of bow) to the neck, increases the space between the strings and the frets, allowing them to vibrate freely without buzzing. If there is too much relief, the strings will be too far from the neck, the instrument will be uncomfortable to play, and intonation could be compromised.



Can you use B string High E?

Re: Using a B string for the high E string.



Yes. It would snap, and the tension trying to get an E would damage the neck. I wouldn’t advise replacing a string from a different gauge set either; even if it is the same string you have spare.

Are the B and E strings the same?

The E string on a guitar is the largest string. It is wound in a bronze colored metal. The B string is very thin (the second thinnest).

Why does my E string buzz on my guitar?

There you have it. Three common causes for fret buzz: (1) uneven frets (2) excessively low string action, and (3) a back bowed neck. Just one of these problems is enough to cause fret buzz, but often times a guitar has a combination of these three problems all at once.

How do you fix a high E string buzz?

If it’s just that high E on the first couple of frets, try slipping a thin piece of paper, or something between the string and the slot, then tune it back up. If the buzzing goes away, here’s another trick. Instead of replacing the nut, get a tiny bit of baking soda and super glue.



How do I stop my E string from buzzing?

Here are five reasons why your strings are buzzing:

  1. Fret in the Right Place. Make sure you’re fretting notes at the proper spot just behind the fret. …
  2. Apply the Right Amount of Pressure. …
  3. Avoid Strumming Too Hard. …
  4. Consider the Strings. …
  5. Check the Setup.


Why does my e cord rattle?

Rattle occurs when vibrating strings make contact with the frets. The vibrations interfere with the string oscillation and lead to an impure sound. The energy in the string is partially absorbed by the rattle which leads to a quicker decay of the tone.

How do I stop low E buzzing?

And what it does is it bends the neck. This way or this way making the strings. Higher or lower and the last thing that would cause a buzz is maybe your neck is warped and you might need a new guitar.



How do I stop my guitar strings from rattling?

So fret the fret that joins at the body and then the first fret. And you can hear that. There's some space in between. There. And the buzz is gone so just experimenting with adjusting your tress rod.