Recording an amp using headphone out?



Asked by: Missy Sanchez

Can you record from headphone out on amp?





Yes, you can use a headphone out into a line in. Just keep in mind that a headphone output power is stronger than line level power. You will not hurt the headphone amp at all because it’s made to drive a much lower resistance, anything higher than 30 ohms is completely safe.

How do you record headphone output?

Enter “Sound Recorder” to run Windows Sound Recorder. Get one earpiece of your headphone closed to your audio source, and then click on the button “Start Recording” on the Sound Recorder to enable this recording program to begin the recording work. Make the audio source play in a clear and maximum volume.

Can you use a headphone jack on a guitar amp as a line out?

Sure, in a pinch it will usually work okay. Headphone amps usually aren’t as free from noise and distortion as good line amps, but in many situations they can be used without significant degradation in overall sound quality.

Can you record sound from amplifier?

For an android phone: Plug a 3mm male to male cord in the headphone out on the amp. Plug the other end of the male to male 3mm into the headphone side of a 3mm audio splitter. Open the recording software that comes with your phone. Plug in the male jack from the splitter (need a 3 ring male) into the phone.

Can I use the headphone jack as an audio output?





Short answer: No. The Headphone Jack is designed as an output only.

Is a headphone output line level?

Line level signals are much hotter than microphone level. Aside from the output of a mic preamp, other examples of line level signals are the headphone output of your phone, the aux input on your car stereo, or the output of an audio mixer.

Can I connect headphone output to microphone input?

The earphone/headphone output from a computer is low impedance, unbalanced, and has a typical signal level of 100 millivolts. It can be connected to an aux input on a mixer, or a high impedance mic input on a mixer. Required is a cable with the proper connectors on each end.

How do I record audio with aux?

Which is a 3.5 to another treatment five millimeter headphone jack. And you need of course your phone to record sound from. So the first step is to plug to the aux cable.

How do you use headphones as input and output?

Control Panel > Sound > Recording > Right-click on your Mic Input > Properties > Listen > Listen to this Device You can then select your Headphones / Default Output Device etc, and your Mic Input will play back through that along with your system audio.



How do you record amps at home?

So it's isolated a little bit at least from the floor. And then I put an acoustic panel on the back of it. And then in front of it I've hung the microphone. That I'm recording it with of Royer 121.

How do I connect my amp to my computer for recording?

You can connect your guitar amp to your computer if the amp has a line-out or headphone socket. Connect the amp’s line-out/headphone to an input on your computer’s audio interface. Some amps also have a USB connection, which can output audio directly into the computer via a USB cable.

Can you plug an amp into an audio interface?

The simplest way to connect a guitar amp to an audio interface is by using an output labeled ‘line out’ on the amplifier. This is sent to the input on the interface using an audio cable, where the signal from the amplifier can be recorded.



How do I connect my headphone amp to my interface?

From here into the monitor outputs on the back of the audio. Interface on the back of the audio interface here i'm just going to connect it to the left output.

Can you plug a guitar directly into an audio interface?

And outs of how you use the audio interface in detail. Let's just have a quick look at the three main ways you can go about recording your guitar firstly. You can record it directly by plugging it

How do you record a tube amp?

Basically you want to point the mic. At the amp and not away from the amp. There's two speakers in this to 12-inch speakers I'm using the off-axis technique.

What is the best way to record guitar amps?

What is the best way to record electric guitar?



  1. Place a microphone in front of your guitar speaker.
  2. Place a microphone in front of your guitar speaker using an isolation box.
  3. Using a (real) amplifier with a load box and use impulse responses to replace the speakers and microphones digitally.

How do you record a guitar amp silently?

Baby cable pedals if you want to use them tube amps this everything up to this point is totally normal like any other Guitar Rig. But this is the point where it gets kind of different.