How to dampen an amp’s volume for recording?



Asked by: Kim Leotta

How can I record my guitar amp quietly?





You just have to crank up they gain a little bit more on your audio interface to compensate for your amps being a little bit quiet.

How loud should my amp be when I record?

well, what you really want to do is have it loud enough so that the microphone hears the tone you want to record. There’s not much sense in choosing your tone based on how it sounds “in the room” if you’re miking your amp at a distance of only a few inches from the speaker.

How do I keep stage volume down?

To keep your stage volume down, here are some things you can try:

  1. Elevate your amp or tilt it up. …
  2. Practice getting your tone at a lower volume. …
  3. Practice stage volume at rehearsal. …
  4. Stand as close to the monitors as possible. …
  5. Be on the same axis as the monitor. …
  6. Don’t be afraid to ask the sound engineer for more.

How do you get good distortion at low volume?

Most important thing is to use pedals instead of amp. Drive now i'm a pedal head some people are not into pedals i love pedals. Here's the thing tube amps need to be pushed to sound good overdriven.

Should you record guitar dry?





Most engineers and mixers favor dry, since it is easier to add effects than it is to take them away. The primary argument being that if a guitar is recorded with reverb and or delay, it can cause problems later on as the mix builds, particularly if there’s too much of either.

Do I need a preamp to record guitar?

No, you don’t need a preamp to record guitar. Preamps boost the original sound of the guitar before feeding it into the amplifier and can produce higher levels of feedback and distortion. Unless you intentionally want the distorted guitar sounds (think Jimi Hendrix), you don’t need a preamp.

What dB to record guitars at?

Recording guitar at around -14 dB is a good starting point. The most important point to keep in mind is to avoid clipping. Recording guitar at around -14 dB should avoid clipping, but you may need to raise or lower your level depending on your style of playing.

Where do I put my amp when recording?

Basically you want to point the mic. At the amp and not away from the amp. There's two speakers in this to 12-inch speakers I'm using the off-axis technique.

How many dB is a guitar amp?

How loud is a guitar amp in decibels? Most guitar amps are around 115 dB if you’re located a meter (or 3.28 feet) away from the speaker/cabinet. However, if you’re standing right next to the speaker of a fully distorted 700W head with a 4×12 cabinet, it’s about 135 dB.



Does attenuation affect tone?

Tone changes



In practice, the use of attenuation does change tone, but blaming the attenuator isn’t always justified. Our perceptions of toppiness and bassiness change depending on volume level.

Can you attenuate a combo amp?

COMBO AMP: When using an attenuator with a combo amp, place the unit between the amp’s speaker out and the speaker itself. Most combo amps have internal speakers that can be unplugged from the amp chassis using a 1/4″ phone plug.

How do you get crisp distortion?

5 Tips To Get Clean Distortion



  1. Practice muting. It’s important to practice muting and mute the unwanted strings when playing with distortion – this ensures no accidental sound and noise. …
  2. Adjust amp settings for clean distortion. …
  3. Use overdrive pedal instead of distortion (or fuzz) …
  4. Use noise suppressor pedal.


How can I record my guitar amp at home?

What is the best way to record electric guitar?

  1. Place a microphone in front of your guitar speaker.
  2. Place a microphone in front of your guitar speaker using an isolation box.
  3. Using a (real) amplifier with a load box and use impulse responses to replace the speakers and microphones digitally.

How do you record on a guitar amp?

Basically you want to point the mic. At the amp and not away from the amp. There's two speakers in this to 12-inch speakers I'm using the off-axis technique.

How do you mic a guitar amp to record?

For more mids, position the mic closer to the center of the speaker. For a darker sound, move toward the edge of the speaker. Start with the mic pointed directly at the amp’s speaker, but experiment with angling the mic at a 45-degree angle if you want to fine-tune what you’re hearing.



How can I record my guitar without audio interface?

Yes, you can record without an audio interface. Instead, try recording with an adaptor plugged directly into your computer, a USB microphone, virtual instruments, or a tape recorder. While these methods don’t require an audio interface, they typically result in lower sound quality.

Do I really need an audio interface?

While you technically don’t need an audio interface to record anything, you’ll need an audio interface to record professional, high-quality sound. That can include recording instruments, voices, or other types of audio. Sure, you’ve got a sound card in your cell phone and a sound card in your computer.

Can you plug a guitar straight into an interface?

Plug straight in (a.k.a. DI or Direct Injection)



The simplest way to capture your guitar is to plug it directly into your audio interface’s instrument input: just connect your guitar cable to one of the quarter-inch jack inputs. (Make sure you press the ‘Inst’ button to engage the high-impedance (hi-Z) circuitry).

Do I need an amp to record?

Recording without an amp can be done with the use of audio interfaces, direct boxes, and amplifier simulator software. You plug a line in from your guitar directly to whichever you plan to use.



Do I need a preamp if I have an amp?

Yes, you need both.



A power amp expects a signal at line level; a preamp is needed for that. You could technically go from a preamp, straight to active speakers without an external dedicated power amp.

Does a bass need an amp?

An amplifier is necessary for an electric bass guitar. Try to find one with a headphone jack for practice. Instrument cable. The instrument cable is used to connect your bass guitar to your amp.