Getting the right balance of frequencies in mix?



Asked by: Josh Cheney

Balancing the high-frequencies

  1. Set the filter to only react to the highest frequencies of the sound. …
  2. Set the ratio to around 1:1.5.
  3. Change the threshold so the audio you want to effect surpasses the threshold.
  4. Now increase the amount until the audio feels like the top end is glistening.

How do you get a good mix balance?





So the only way you can do that and get that right when you're mixing to get your balance to get the focus point work backwards down the team is to listen. So quietly.

What should a balanced mix look like?

A balanced mix (or flat, if you prefer) usually has a full range of frequencies more or less hitting 0dB on an FFT reader. You can go -/+3dB around it, but keeping it around 0 is the best. For electronic music, it’s pretty normal to have the low end sticking out by about +3dB though.

How do you check tonal balance in a mix?

Areas are stacking up against the target. So the blue highlighted. Area is where you want to be sitting. If you toggle over to fine you can see sort of the generalized curve.

How do you balance a sound mixer?

Adjust the pan knobs to put the channel’s audio in the left or right speaker. The pan knobs control the balance between the left and right speakers, and they are usually located directly above the channel faders. When the knob points down the middle, the audio will play equally through the left and right speakers.

What dB should beat be in a mix?





So long as your mixes give the mastering engineer room to work, and cover your noise floor, then you’re in a good range. I recommend mixing at -23 dB LUFS, or having your peaks be between -18dB and -3dB.

How do you fix clashing frequencies?

Try around 1.5 kHz for a sharp, aggressive sound, or boost the low-mids to add power and “oomph.” You can also use a mid-side EQ to further enhance the separation by boosting each frequency range in a different part of the stereo spectrum.

Should snare be louder than kick?

The snare is the foundation of the backbeat, and typically one of the loudest elements in the mix. Next, bring the kick fader up until it sounds almost as loud as the snare. It should be loud enough that the low frequencies are rich and powerful, but not so loud that it masks the bottom-end of the snare drum.

How can you tell if a song is mixed well?

How To Tell When Your Mix Is Finished

  1. You Can Hear Each Instrument Clearly.
  2. You Can Understand Every Word of the Lyrics.
  3. The Mix Is Glued Together.
  4. There Are No Technical Issues with the Mix.
  5. It Grows and Changes Over Time.
  6. It Sounds Good Compared to Other Songs.
  7. It Sounds Good on Multiple Sound Systems.

Should the beat be louder than the vocals?

Your vocals shouldn’t be louder than the beat in most cases. However, some genres, like pop music, sometimes have vocals slightly louder than the beat to emphasize the beat. Since vocals are the most important aspect of many genres, it’s best to maintain a balance between vocals and the beat.



How do you equalize a mixer?

The position of the black knob is immaterial. Base is set at 80 Hertz low frequency rather this is a simple boost. And cut so that's your EQ.

What levels should my mix be at?

To summarize: before sending a mix off to a mastering engineer, make sure you leave around -6dB Peak volume, and -18 LUFS integrated in headroom. If you’re mastering for streaming, focus on around -12 LUFS integrated, but be careful not to mix too loud or not loud enough to not sacrifice any necessary dynamics.

How do you properly mix?

If I press play. So what I'm going to do is pull the volume faders all the way down.



How do I make my mix sound professional?

How To Make My Mix Sound Professional: 10 Golden Rules

  1. 1) Do your Gain Staging. …
  2. 2) Do your bus routing. …
  3. 3) Compress in stages. …
  4. 4) Filter out unwanted frequencies. …
  5. 5) Use gear and/or plugins to give character. …
  6. 6) Sort out the low end. …
  7. 7) Do parallel compression. …
  8. 8) Do your panning and spatializing.

What are the 5 tips to keep in mind when mixing audio?

Summary

  • Make your track right starting from the arrangement process. Paint the frequency spectrum and make sure your track sounds good even without mixing first.
  • Think in terms of separating or layering your sounds. …
  • Panning. …
  • Use compression the right way. …
  • Depth.


What makes a good mix?

A great mix will well-defined enough for the listener to pick out individual sounds. Panning: Every element in the song is placed in a way that makes sense to the artist and listener. Space: Various elements in a song as well as the overall mix should have a sense of ambience.



How do you make a smooth sounding mix?

The most effective way to solve harshness is to improve your overall tonal balance in your mix. You might find that the 1kHz-10kHz region is loud relative to your low-end and low-mids. A boost in these areas can alleviate the harshness.

How do I make my mix sounds clearer?

10 Mixing tips and tricks to create a clear mix

  1. Bass your worse enemy.
  2. Use Reverb as delay.
  3. Side chain compress the import parts that need it.
  4. Parallel compress your drums.
  5. avoid the stereo imager in the mix use mid side routing instead.
  6. phase / delay to create space.
  7. notch filter to create space.