Electric guitar amp won’t switch to distortion channel?



Asked by: Sam Cobain

How do you turn on amp distortion?





Turn knobs marked “gain” or “overdrive” all the way up. Turn other volume knobs down to get the loudness you want. Once you’ve proved you can get heavy distortion, dial things back to find the tone you want. Some amps won’t distort at low volumes.

How do I change my guitar from clean to distortion?

When you need to play with a clean sound, make sure the gain pedal is off. When you need to switch to distortion, push the gain pedal using your foot to turn it on – which changes the sound to distortion immediately. Keep in mind that sound changes the moment you push the pedal with your foot.

How do I get distortion on my electric guitar?

A volume pedal is connected between the guitar and amplifier. When an amplifier is being used to distort the sound,the quality of the sound changes according to the volume. When the volume is low there is little distortion. Pressing the pedal down gradually increases the volume-and the distortion.

Why is my guitar amplifier not working?

Check if the amp or PA you are plugged into is turned on. If using a mixer, make sure it’s not muted and that all cords are plugged in all the way. Is the amp/cable working with other guitars? Always make sure your amp is working and the cables are in good working condition.

Can I get distortion without pedal?





You can easily get a distortion without a pedal with your amp and guitar only. It’s not just a matter of saving the money but a matter of a better-distorted sound. The right amp is the key to reaching a nice, warm, and round distortion you desire.

Is gain the same as distortion?

gain is the amplification factor, basically the ratio of output over input. the more you turn the gain knob up, the more overdrive/distortion you get, basically. Distortion is just more extreme overdrive. Both the 5150 and vh4 are high gain amps, and both are capable of producing distortion.

How do I get overdrive on my amp?

This means either turning it up as loud as it can go, or—if your amp has a master volume control—turning up your “gain” knob but leaving the volume fairly low. (On some amps, there are separate knobs for “volume” and “master.” To get overdrive, turn the “volume” knob way up, but leave the “master” knob fairly low.)

How do you distort an amp clean?

Simply switch the channel to achieve distortion. If you happen to have an amp with a single channel (only clean), then you can still get distortion effects by adjusting the EQ controls – maximum mid, lower treble, higher gain and lower master volume.

Do you use a distortion pedal on clean?

i got a ds-1… and i use it on clean… “If it seems like you are playing around and not practicing, that’s when you know you really love it.” Use it however you want, but bear in mind that gain boosting pedals sound like crap on the distortion channels of solid state amps – they work fine on tube amps though.



How can you tell if an amp is blown?


You can usually tell if it's blown because the piece in the middle is gonna be split apart if this fuse is blown it means either there's a problem back by the amplifier.

How do I know if my guitar amp is blown?

The most common aural indication of a blown speaker is an unpleasant buzzing or scratching sound, by itself or roughly at the pitch of the note the speaker is attempting to reproduce. Or there could be no sound at all.

How can you tell if an amp is bad?

Test the sound by unplugging the sound cables or colored RCA wires.



  1. Hissing and crackling are often easy to fix by rearranging the wires or getting complimentary speakers.
  2. If the noise doesn’t stop, then you probably have a faulty amp to replace.


How do I test my amp channels?

My my amplifier is REM for remote yours might say plus turn on or remote. You know depending on your model. Then of course your. Ground. You can see my red light came on which is my Diagnostics.

How do you test a guitar amp?

So switch it on the light come on I usually put it on the game Channel and turn everything up. So if you can hear that hissing sound your amp is obviously working.

How do you test a amplifier if it works?

How To Test An Amplifier



  1. Attach the wires for power (red) and ground (black). …
  2. Touching the amplifier’s electricity wire to the car’s battery positive post and the ground to the negative battery post is one of the easiest things. …
  3. Link the amplifier with a mic. …
  4. Check all accessible fuses and use one fuse in the amplifier.

What can damage an amplifier?

The two most likely possibilities for damage are: – Connecting the speakers incorrectly, putting a heavy load on the amplifier and overheating it. Usually one channel goes before the other. – Cranking up the volume on the amp and ruining loudspeaker driver(s).

How do I test an amp with a multimeter?

Insert the Test CD into the source unit. With the A.C. Voltmeter set to ~ AC VOLTS, in a range of 10 to 100 Volts, connect the voltmeter (+) test lead to a single channel of the amplifier (+) output. Connect the voltmeter (-) test lead to the same amplifier channel’s (-) terminal.