Do I need an effects loop in a bass amp?

Asked by: Robin Hall

Short answer: you don’t need the loop for bass. In my opinion you don’t really even need pedals, but they can be fun. Based on the answers to my question about bass effects, this answer sounds spot on. Most folks seem to rely on pre-amp effects and avoid timing effects.

Is an effects loop necessary?

An FX Loop is essential an insert point in your amplifier circuit that allows you to insert a piece of gear after the preamp circuit, but before the power amp circuit. Some guitar players are happy to run everything into the front end of the amp, and others prefer to insert certain effects types into the loop.

Is it better to use the effects loop on an amp?

So, to answer the question, should I use an effects loop? You should use an effects loop if: You use the distortion on your amp if you want your delays and reverbs to be clearer than ever whilst using a distorted amp.

What can I use if I don’t have an effects loop?

So if you have an amp that doesn't have an effects loop an. Easy way to do it is if you mic it up use the loop in the board.

Why do amps have effects loops?

An effects loop allows you to place pedals after the pre-amp stage of the amplifier. This is useful because some effects such as modulation, reverb and delay sound better when placed after distortion. An effects loop ensures these effects are placed in the optimal position in the signal chain.

Can you use a looper without an effects loop?

Re: Question – Looper pedal with amp without effects loop

Yes, it works ok. Not the same as through an amp with fx loop, but it’ll suffice. AND you will learn a lot on how the guitar can sound just by turning a knob.

How do you use the effects loop on a bass amp?

And an effects loop so essentially the way it's designed is to plug your instruments straight in take the effects loops. And run it through your chain of pedals.

Should distortion be in effects loop?

To summarize, we would not recommend putting a distortion pedal in your effects loop. Instead, put it in the main line between your amp’s input and your electric guitar. It’ll help the distortion pedal interact better with your preamp and will sound more natural when moving from a clean to a distorted sound.

Can you put a compressor in the effects loop?

You can do the same thing on your pedalboard, either by placing your compressor in the FX loop of your amp, after a good overdrive pedal or, our favourite, using your compressor after a really great amp-in-a-box-style pedal, like the Origin Effects RevivalDRIVE series.

Is an effects return the same as a power amp in?

They are pretty much the same thing but labeled differently. An effects loop send and return or preamp out/power amp in are basically an insert point between the amplifiers preamp section and power section. There are exceptions. The Orange should work fine for your purposes.

What are the benefits of an effects loop?

If the distortion/overdrive is coming from the amplifier itself, using the effects loop allows you to place effects, such as delay, reverb, and rotary speaker, after the distortion. This normally results in a better result — running a delay into the front of a distorted amp can result in a muddy, messy sound.

Does delay go before distortion?

Putting a delay pedal before distortion means that the echoes from the delay pedal would themselves become distorted, resulting in an unnatural and messy sound. If you’re using an overdrive and a boost, it’s wise to put the boost first – that sends a stronger signal into the overdrive to get the most out of it.

How do you connect an effect pedal to an amp?

How to Connect Effects Pedals to your Amp and Guitar

  1. Make sure your amp is turned off.
  2. Connect your guitar cable to your guitar.
  3. Then plug the other end into the “input” side of your pedal.
  4. Plug another guitar cable into the “output” side of your pedal.
  5. Then plug the other end into the “input” on your amp.

Can I loop with spark amp?

With the AIRSTEP and your Smart Device, you can finally get a REAL looper for your Spark Amp! In the video, the AIRSTEP Foot controller is set to switch channels of Spark and toggle recording of the Looper App.

Can I use a looper with any amp?

Of course you can. It runs just like a normal pedal. You dont have to have an effects loop for anything. Some pedals sound better in the effects loop.

What amps have a looper?

If you’re interested in learning more about the best amps with loopers in them, you’ve come to the right post!

  1. Line 6 Spider V 240 MKII.
  2. Blackstar ID:Core 100.
  3. Roland CUBE-40XL.
  4. JOYO DC-15S.
  5. Roland AC-33.
  6. Peavey Vypyr X 3.
  7. Fender Mustang GTX 50.

Do I need an amp to use a loop pedal?

In theory, yes you can. Some high-end loop pedals have dedicated headphone outputs for this purpose. However, plugging headphones into a normal output is not recommended.

Does positive grid have a looper?

Whether you’re looking for a simple practice tool for jamming along to a chord progression or for working on a lead solo for your song, the Looper/Recorder feature in BIAS FX 2 is your best companion.