Am I using my noise gate wrong?



Asked by: Kris Pressley

What should my noise gate be set to?





Usually, a fast attack is your best bet when using a noise gate. You don’t want the beginning of a drum hit or vocal line to get cut off. So make sure your attack is fast enough that your recording isn’t getting clipped. Start with something under 5 ms and adjust from there.

Does a noise gate help with background noise?

Gates work well on any sounds in a signal that may be quieter than the desired sound you are capturing (like a snare, or a tom). Noise Gates will help remove: Ambient background noise. Unwanted reverberation.

Should I record with a noise gate?

You could also use a noise gate while recording to prevent these unwanted noises from even being recorded. This technique, however, is not recommended as you might end up gating out audio that you want. Noise gating is a powerful tool that, when used correctly, will improve the quality of your audio immensely.

Does a noise gate go before distortion?

Noise Gate Placement



If you are, place the noise gate before these effects, otherwise it will interfere with their performance. Some also like to put their noise gate after their high gain pedals such as overdrives or distortions.

Do noise gates affect tone?





All in all, noise gate pedals do affect tone. However, that change in tone may not be too strong to notice. Regarding the setting, there are a few things to consider. The threshold, which decides when the gate opens and closes, will affect the sound depending on how low or high you set it.

Where should noise gate go in pedal chain?

Where does a noise gate go in your signal chain? In some ways, this is subjective. Naturally, you’ll want to place the noise gate wherever the noise is, for example after your fuzz pedal. It’s most common, however, to put it at the end of your chain but before any ambient pedals such as delay and reverb.

What is the difference between noise gate and noise suppression?

A Noise Gate defines thresholds that fully open allowing all of the sound to pass, or fully close to block the entire signal. A Noise Suppressor can also do this but has the added capability to let some of the signals sound pass by adjusting the sensitivity of the open / close thresholds.

How do you use a vocal noise gate?


So in this case his vocal is somewhere up here it's not falling below the gate open level and then when it does for his breaths or for his pauses the expansion.

How do I stop my mic from picking up background noise?

If are using a noise-canceling microphone, make sure it is positioned close to the mouth, approximately 2 centimeters or less than 1 inch away from the mouth. This filters out unwanted background noise, so it is important that you position it correctly to avoid audio issues.



Should I use a noise gate pedal?

Noise gate pedals attenuate a signal that is below a certain threshold. That means that it cuts the signal and avoids unwanted hum. Therefore, when your gear produces undesired sounds, then noise gate pedals will be required.

Are noise gate pedals worth it?

It really all depends on the order; if you have pedals before the distortion section you don’t have to include them in the loop, but generally any pedals after the distortion you’ll want to include because otherwise you can end up with a huge mess of cables.

Do noise gate pedals work?

It takes a little bit of time to figure it out, but it’s certainly worth it and quite easy to use once you get the hang of it. The Sentry noise gate pedal works great for removing single-coil hum without infringing on the tone. When in Hiss mode, it’s also easy to find the threshold.



How do you adjust a noise gate pedal?

Start with the threshold at its minimum value and then while slightly muting the strings with your right hand slowly turn the threshold up until the noise is only just gone.

What are the four main controls on a noise gate?

Noise Gate Controls

  • Threshold. The threshold sets the level at which the gate opens and closes.
  • Attack. The attack determines how quickly the gate opens. …
  • Release. The release determines how quickly the gate closes. …
  • Hold. …
  • Range.


What is the difference between a noise gate and a compressor?

Noise Gate



These pedals are very similar to compressors in that they are specifically used to alter an instruments signal level but whereas compressors are used to make sure a signal is above a certain threshold, noise gates attenuate signals which register below the threshold.



Should a noise gate go before or after a compressor?

It is important to place a compressor after a noise gate in most situations. For a gate to be most effective on drums, the level of the unwanted noise has to be significantly quieter than the actual drum hits.

Can you put a noise gate after a compressor?

Putting a noise gate after the compressor will clean up the hiss but it will not remove mistakes that your playing is introducing. It will also clamp some of the notes, and depending on your settings and the quality of the gate this can mess with your tone.

Is a noise gate a limiter?

A limiter (which is an extreme case of compression) will simply block the signal from going any higher than the threshold. With makeup gain, you can then increase the perceived loudness of the quieter parts of the signal. By contrast, a noise gate acts as the opposite of a limiter.

What does a compressor gate do?

That right on down that's the gate function compressor compresses the distance from the loudest sound to the quietest sound so think of sound as a sound wave.